Bretford LAP24EBA Bedienungsanleitung

LAP24EBALAP24EFRNOTEBOOK CART ASSEMBLYAssembly Instructions for:INTERIOR E-UNITREPOSITIONING / REPLACEMENTANDTIMER INSTALLATIONParts ListQty. Pa

Step 4Reinstall the 7 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the bracke

Step 6Reinstall the E-Units (set aside from being removed from the rear) as follows:1. Rotate the E-Unit 180 degrees (from original position).2. Posit

E-UNIT REPLACEMENT:'REAR LOCATION'NOTE:UNPLUG CART POWER CORDS FROMPOWER SOURCE BEFORE STARTINGStep 1Remove 14 screws (2 per shelf) from r

Step 2With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mountingtabs) shown in Detail 'B',

DETAIL 'C' DETAIL 'D'Step 3Remove E-Unit(s) by griping the top and tilt it side ways until it clears the underside of the cart int

Step 4Carefully install replacement E-Unit(s) into position by placing bottom in first and tilting in sideways to the top.When repositioned correctly,

Step 5Reinstall the 7 interior shelves as follows:1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the brack

Step 1Open both front doors of cart to access E-Unit(s). Unwind any length of E-Unit power cord remaining on theexterior rear panel cord wrap bracket

clipDETAIL 'A'DETAIL 'B'bracketassemblybracketassemblyStep 2Remove E-Unit(s) by griping the top and tilt it side ways until it cle

Step 3Carefully install replacement E-Unit(s) into position by placing bottom in first against the offset and tilting it insideways to the top.When re

clipDETAIL 'A'DETAIL 'B'E-Unit powercordbracket assemblybottom shelfFront Viewbracketassemblybracketassembly

TIMER INSTALLATION:'E-UNIT AT REAR LOCATION'NOTE:UNPLUG CART POWER CORDS FROMPOWER SOURCE BEFORE STARTINGDETAIL 'A'Step 1Remove 6

Step 2With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf frommounting tabs) shown in Detail &apo

Step 5Install timer with 2 screws. Adjust timer dial to current time.Step 4Remove filler bracket from bracket by pulling upward.Discard filler bracke

Step 6Step 7Reinstall the 3 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on the

DETAIL 'C'Step 8Reinstall 6 screws to rear panel that will secure the 3 interior shelves(see DETAIL 'C'). DO NOT OVER TIGHTEN SCR

SEE DETAIL 'A'SEE DETAIL 'B'bottom shelfTIMER INSTALLATION:'E-UNIT AT FRONT LOCATION'NOTE:UNPLUG CART POWER CORDS FROMP

front-rightfront-leftStep 2Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interiorshelf c

Step 4With both doors open, remove the 3 bottom interior shelves by carefully pushing upward (to release shelf frommounting tabs) shown in Detail &apo

Step 5Remove 2 screws from bottom flange (securing bracket to bottom of cart) and remove bracket assembly.bottom flange-timer/bracketStep 6Remove fill

Step 7Install timer with 2 screws. Adjust timer dial to current time.Step 8Install timer/bracket assembly onto bottom, rear of cart with 2 screws. F

Step 2Remove front-left E-Unit by griping the top and tilt it side ways until it clears the underside of the cart interiorshelf channel and set it asi

notchtabStep 9Reinstall the 3 interior shelves as follows:1. Carefully slide in the shelf with notch at the bottom position (the notch will rest on th

front-rightfront-leftStep 11Carefully reinstall E-Units into position by placing bottom in first against the offset and tilting it in sideways to thet

$8;$8;$8;$8;$8; $8;LABEL INSTALLATION:E-Unit at frontsuggested label directionsug

Part #031-6608Rev. 08.29.05 CHPAD LOCK - DOOR:Bretford Bretford Ltd.11000 Seymour Avenue Technology HouseFranklin Park, IL 60131 2 Etongate, 11

DETAIL 'D'Step 4Remove each interior shelf by carefully pushing upward (to release shelf from mounting tabs) shown in Detail 'D',t

clip-rearStep 5Reinstall the E-Units (set aside from being removed from the front) as follows:1. Rotate the E-Unit 180 degrees (from original position

Step 6Reinstall the 7 interior shelves as follows:1. Carefully slide in the shelf with notch, at the bottom position (the notch will rest on the brack

Step 1Remove 14 screws (2 per shelf) from rear panel that secure the 7 interior shelves (see DETAIL 'A').DETAIL 'A'E-UNIT REPOSITI

Step 2With both doors open, remove each interior shelf by carefully pushing upward (to release shelf from mountingtabs) shown in Detail 'B',

DETAIL 'D' DETAIL 'E'Step 3Remove rear-left E-Unit by griping the top and tilt it side ways until it clears the underside of the c